Siemens HZM Installation Instructions Manual
Remote conventional zone module
Hide thumbs
Advertisement
Quick Links
Installation Instructions
Model HZM
Remote Conventional Zone Module
INTRODUCTION
Controls And Indicators
PRE-INSTALLATION
P/N 315-034850-8
The Model HZM from Siemens Industry, Inc. is an intelligent device that connects a
single zone of conventional devices to a DLC (FireFinder-XLS System) or FS-DLC (FS-
250 System) device loop. The HZM can power up to fifteen compatible 2-wire, ioniza-
tion or photoelectric smoke detectors or it can power one PB-1191 Beam Detector. It
can also monitor an unlimited number of shorting devices such as waterflow switches,
thermal detectors, manual stations, etc.
Each HZM can be assigned a custom message using either the Zeus Programming
Tool (FireFinder-XLS System) or the FS-CT2 (FS-250 System). Refer to the Zeus Quick
Start Manual, P/N 315-033875, or the FS-250 Programming Manual, P/N 315-049403,
as applicable. The alarm verification configuration is used only for non-shorting detectors.
The HZM supports Class A and Class B wiring. The module uses one address on the
device loop. It does not require any mechanical address programming. Use the DPU
Device Programming Unit to program and test the module.
FRONT
HZM
ALARM
Figure 1
HZM Module
The HZM is not listed for use in mass notification applications.
The HZM has a multicolor LED, visable through the cover plate, which indicates the
condition of the circuit. This multicolor LED displays red for alarm, yellow for trouble,
and green for normal operation (See Figure 1).
Setting The Module Address
1.
Using the DPU Device Programming Unit, plug the programming cable into
the programming points on the HZM (See Figure 1).
2.
Set the address for the HZM by following the instructions in the DPU
Manual, P/N 315-033260.
BACK
HZM
1
2
3
4
5
6
7
8
9
Siemens
Siemens
Siemens Industry
Siemens
Siemens
Building
Building
Building
Building
Building T T T T T ec
SIDE
PROGRAMMING
POINTS
Industry
Industry, , , , , Inc.
Industry
Inc.
Inc.
Industry
Inc.
Inc.
ec
ec
echnologies Di
ec
hnologies Di
hnologies Di
hnologies Di
hnologies Division
vision
vision
vision
vision
Advertisement
Related Manuals for Siemens HZM
Summary of Contents for Siemens HZM
- Page 1 The alarm verification configuration is used only for non-shorting detectors. The HZM supports Class A and Class B wiring. The module uses one address on the device loop. It does not require any mechanical address programming. Use the DPU Device Programming Unit to program and test the module.
-
Page 2: Installation
Initiating Devices (Figures 2, 3, and 4) The HZM supports one zone of initiating devices in either Class A or Class B. The initiating devices are connected to terminals 5–8 on the HZM terminal block. The HZM is a polarity insensitive module and terminals 1 and 2 can be connected to either line of the DLC or FS-DLC Device Loop. - Page 3 Remove the 2-position plug from J1. Reassemble the circuit board and plastic cover using the screw that was removed in the first step. Be sure to use the correct end of line device with the HZM in this configuration. BEAM DETECTOR WIRING CLASS B/STYLE B...
- Page 4 <60K ohms for terminals 5-8 on HZM. The HZM communicates with the FS-250 via its FS-DLC device loop. The device loop may be wired Class A or Class B. Figure 6 shows both wiring types. Refer to the FS-250 Installation, Operation and Maintenance Manual, P/N 315-049353, for addi- tional wiring information.
- Page 5 24V power output on the control panel or auxiliary power supply. The 24 VDC power may be wired only as Class B. Since the HZM monitors the power at its screw terminals, you can star or T-tap the power connection. Refer to Figure 7 for the wiring diagram.
-
Page 6: Electrical Ratings
ELECTRICAL RATINGS i t i l i f l l u Siemens Industry, Inc. P/N 315-034850-8 Building Technologies Division... -
Page 7: Cyber Security Disclaimer
Cyber security disclaimer Siemens products and solutions provide security functions to ensure the secure operation of building comfort, fire safety, security management and physical security systems. The security functions on these products and solutions are important components of a comprehensive security concept. - Page 8 This page has been left intentionally blank. Siemens Industry, Inc. Siemens Canada, Ltd. Document ID A6V10233195 P/N 315-034850-8 Building Technologies Division 1577 North Service Road East Florham Park, NJ Oakville, Ontario L6H 0H6 Canada...